{"id":33786,"date":"2026-11-10T11:59:03","date_gmt":"2026-11-10T08:59:03","guid":{"rendered":"https:\/\/epcas.com.tr\/?p=33786"},"modified":"2026-11-10T11:59:03","modified_gmt":"2026-11-10T08:59:03","slug":"railway-dc-power-supply-signalling-point-machines","status":"publish","type":"post","link":"https:\/\/epcas.com.tr\/en\/railway-dc-power-supply-signalling-point-machines\/","title":{"rendered":"DC Power Supply for Railway Signalling and Point Machines"},"content":{"rendered":"<p dir=\"ltr\" data-path-to-node=\"0\"><span class=\"\">On a railway,<\/span> very few things are allowed to fail quietly. A signal that goes dark defaults to danger and stops trains. A set of points that loses power in mid-throw leaves a route unproven, and the interlocking will not clear a signal over it. Either way, traffic stops. The <b data-path-to-node=\"0\" data-index-in-node=\"276\">railway DC power supply<\/b> behind signalling equipment and point machines is therefore not an auxiliary system. It is part of the safety chain.<\/p>\n<p dir=\"ltr\" data-path-to-node=\"1\">Most railway signalling and point machine installations still run on DC, typically 110 V or 125 V, backed by a battery that keeps everything alive through a mains failure. This article explains how to design such a system, with a focus on the load that makes railway DC supplies unusual: the point machine. We draw on two projects we have delivered: a 110 V DC, 60 A, four-unit parallel redundant rectifier system for a railway line in Indonesia, and a 125 V DC, 30 A SD Series rectifier for a transportation application in the United Kingdom.<\/p>\n<blockquote>\n<p dir=\"ltr\" data-path-to-node=\"1\">Our <a href=\"https:\/\/epcas.com.tr\/en\/product-category\/industrial-rectifier\/\">Industrial Rectifier<\/a> range converts AC supply into controlled DC output for industrial and transport installations.<\/p>\n<\/blockquote>\n<h2>What the DC Supply Has to Feed<\/h2>\n<p>A typical signalling equipment room or trackside location cabinet supplies several classes of load from the DC bus:<\/p>\n<ul>\n<li><strong>Point machines (switch machines)<\/strong> that move the switch rails between normal and reverse<\/li>\n<li><strong>Interlocking and object controllers<\/strong>, electronic or relay-based<\/li>\n<li><strong>Track circuits and axle counters<\/strong><\/li>\n<li><strong>Signal lamps or LED signal heads<\/strong>, sometimes through DC\/AC inverters<\/li>\n<li><strong>Telecommunications and SCADA equipment<\/strong><\/li>\n<\/ul>\n<p>The steady-state load is often modest. The problem is the point machine.<\/p>\n<h2>The Point Machine Load Profile<\/h2>\n<p>A DC point machine is essentially a motor driving a gearbox, a throw bar and a locking mechanism. When the interlocking commands a move, the motor starts against the full mechanical load of the switch rails. Starting current is several times the running current, and the whole movement typically lasts a few seconds.<\/p>\n<p>A typical throw looks like this:<\/p>\n<ol>\n<li><strong> Inrush:<\/strong> high current for the first fraction of a second as the motor starts from standstill<\/li>\n<li><strong> Running:<\/strong> a lower plateau while the rails move<\/li>\n<li><strong> Locking:<\/strong> a short rise as the mechanism drives the lock home<\/li>\n<li><strong> Stall or end of stroke:<\/strong> the clutch slips or the circuit opens<\/li>\n<\/ol>\n<p>If several point machines are thrown at the same time, as happens when a route is set through a junction, these peaks add up. The DC supply must hold bus voltage through the combined inrush, or the interlocking electronics on the same bus will see a dip.<\/p>\n<p><em>Typical DC point machine throw: inrush at start, running plateau, locking peak, then end of stroke. Simultaneous throws add these peaks on the DC bus.<\/em><\/p>\n<figure id=\"attachment_33792\" aria-describedby=\"caption-attachment-33792\" style=\"width: 1024px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" loading=\"lazy\" class=\"size-large wp-image-33792\" src=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile-1024x576.png\" alt=\"DC point machine current profile showing inrush, running, locking and end-of-stroke phases during a throw\" width=\"1024\" height=\"576\" srcset=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile-1024x576.png 1024w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile-300x169.png 300w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile-768x432.png 768w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile-710x399.png 710w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-inrush-current-profile.png 1200w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><figcaption id=\"caption-attachment-33792\" class=\"wp-caption-text\">DC point machine current profile showing inrush, running, locking and end-of-stroke phases during a throw<\/figcaption><\/figure>\n<p><em>During a point throw, the battery on the DC bus supplies the inrush peak so bus voltage stays inside limits for the interlocking equipment.<\/em><\/p>\n<figure id=\"attachment_33794\" aria-describedby=\"caption-attachment-33794\" style=\"width: 900px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" loading=\"lazy\" class=\"size-full wp-image-33794\" src=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/point-machine-throw-bus-voltage.gif\" alt=\"Animated point machine throw showing motor current and DC bus voltage with and without battery support\" width=\"900\" height=\"506\" \/><figcaption id=\"caption-attachment-33794\" class=\"wp-caption-text\">Animated point machine throw showing motor current and DC bus voltage with and without battery support<\/figcaption><\/figure>\n<h2>Why the Battery Sits on the Bus<\/h2>\n<p>In a well-designed railway DC power supply, the battery floats directly on the bus alongside the rectifiers. This arrangement does two jobs at once.<\/p>\n<p>First, it provides autonomy through a mains failure. Signalling operators typically specify between 30 minutes and several hours depending on the location and whether a standby generator exists.<\/p>\n<p>Second, and less obviously, it supplies inrush current. A battery has very low internal resistance and can deliver a short peak far above what the rectifiers are rated for. The rectifiers run in current limit for a moment, the battery covers the difference, and the bus voltage barely moves.<\/p>\n<p>Nickel-cadmium batteries are common in railway applications because they tolerate wide temperature ranges, survive deep discharge, and have long service lives in trackside cabinets that see heat in summer and frost in winter. VRLA is used where the environment is controlled and cost is a priority. The charger profile must match the chemistry: NiCd and VRLA require different float and boost voltages, and charging one with the other&#8217;s profile shortens battery life significantly.<\/p>\n<blockquote><p>Our work in the <a href=\"https:\/\/epcas.com.tr\/en\/sectors\/transportation\/\">Transportation sector<\/a> focuses on DC power systems that keep signalling and control equipment running.<\/p><\/blockquote>\n<h2>Parallel Redundancy: How It Works<\/h2>\n<p>A single rectifier, however reliable, is a single point of failure. Railway operators usually specify redundancy, and the most robust form for a DC bus is active parallel redundancy.<\/p>\n<p>In the system we built for the Indonesian railway, four rectifier units operate in parallel on a common 110 V DC bus, together rated 60 A. Each unit:<\/p>\n<ul>\n<li>shares load current actively with the others, so all four run at similar loading and age at the same rate<\/li>\n<li>connects to the bus through an output isolation stage (diode or MOSFET OR-ing) so a failed unit cannot pull the bus down<\/li>\n<li>can be isolated for maintenance without interrupting the bus<\/li>\n<\/ul>\n<p>Because all units are already running, there is no transfer when one fails. The remaining units pick up its share within milliseconds through the current-sharing loop. From the point machine&#8217;s perspective, nothing happened.<\/p>\n<p><em>Four rectifiers share the load. When one fails, the remaining three take over its share within milliseconds, with no transfer and no bus interruption.<\/em><\/p>\n<figure id=\"attachment_33790\" aria-describedby=\"caption-attachment-33790\" style=\"width: 900px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" loading=\"lazy\" class=\"size-full wp-image-33790\" src=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/parallel-redundant-rectifier-failover.gif\" alt=\"Animated parallel redundant rectifier system showing load sharing between four units and automatic redistribution when one fails\" width=\"900\" height=\"506\" \/><figcaption id=\"caption-attachment-33790\" class=\"wp-caption-text\">Animated parallel redundant rectifier system showing load sharing between four units and automatic redistribution when one fails<\/figcaption><\/figure>\n<p>The number of units is chosen so that the loss of one, or sometimes two, still leaves enough capacity for full load plus battery recharge. That is N+1 or N+2.<\/p>\n<p><em>Architecture of a parallel redundant railway DC power supply: four rectifiers with output isolation, battery on the bus, separate fused feeders for point machines and interlocking.<\/em><\/p>\n<figure id=\"attachment_33796\" aria-describedby=\"caption-attachment-33796\" style=\"width: 1024px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" loading=\"lazy\" class=\"size-large wp-image-33796\" src=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture-1024x576.png\" alt=\"Railway DC power supply architecture with four parallel rectifiers, OR-ing diodes, battery, point machines and interlocking loads\" width=\"1024\" height=\"576\" srcset=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture-1024x576.png 1024w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture-300x169.png 300w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture-768x432.png 768w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture-710x399.png 710w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-dc-power-supply-redundant-architecture.png 1200w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><figcaption id=\"caption-attachment-33796\" class=\"wp-caption-text\">Railway DC power supply architecture with four parallel rectifiers, OR-ing diodes, battery, point machines and interlocking loads<\/figcaption><\/figure>\n<h2>Distribution: Separate the Point Machines<\/h2>\n<p>Point machine feeders should be separated from interlocking and electronic feeders, each with its own protection. A fault in a trackside point machine cable, which is exposed to ballast, water and mechanical damage, should not take out the interlocking.<\/p>\n<p>Good practice includes:<\/p>\n<ul>\n<li>dedicated fuses or MCBs per point machine circuit, sized for inrush without nuisance tripping<\/li>\n<li>separate distribution for electronic loads, possibly with additional filtering<\/li>\n<li>voltage drop calculated for the longest trackside cable at minimum battery voltage, while the motor draws inrush current<\/li>\n<\/ul>\n<p>The last point is often missed. Point machines can be hundreds of metres from the equipment room. At 110 V, a cable sized only for running current may deliver too little voltage at the motor terminals during start-up, causing a slow or failed throw.<\/p>\n<blockquote><p>Our <a href=\"https:\/\/epcas.com.tr\/en\/projects\/railway-transportation-infrastructure-indonesia-110vdc-60a-parallel-redundant-rectifier-system-design-and-manufacturing\/\">Indonesia 110VDC railway project<\/a> covers a parallel redundant 110VDC rectifier system designed and manufactured for railway infrastructure.<\/p><\/blockquote>\n<h2>Earth Fault Detection on Floating DC Systems<\/h2>\n<p>Railway DC supplies are normally operated unearthed, with both poles floating relative to earth. A single insulation fault on one pole does not cause current to flow, so the system keeps running. That is a safety feature.<\/p>\n<p>The risk is the second fault. If a second fault appears on the other pole, current can flow through an unintended path. In signalling, that path could energise a relay or a point detection circuit when it should not be energised. This is why continuous insulation monitoring is essential.<\/p>\n<p>The SD Series 125 V DC, 30 A rectifier we supplied for a UK transportation project includes an internal earth leakage detection module. It monitors the insulation of both poles continuously and raises an alarm when resistance falls below the set threshold, long before a second fault can create a dangerous condition. The same unit uses DSP control and a two-stage diode dropper to keep the load voltage within limits while the battery is on boost charge.<\/p>\n<blockquote><p>Our <a href=\"https:\/\/epcas.com.tr\/en\/projects\/transportation-sector-united-kingdom-125vdc-30a-sd-series-dsp-controlled-industrial-rectifier-design-and-manufacturing\/\">UK 125VDC SD Series project<\/a> describes a DSP-controlled 125VDC industrial rectifier built for the UK transportation sector.<\/p><\/blockquote>\n<h2>Sizing Example<\/h2>\n<p>Consider a signalling location with the following loads on a 110 V DC bus:<\/p>\n<ul>\n<li>Interlocking, object controllers and track equipment: 12 A continuous<\/li>\n<li>Four point machines, each drawing 8 A running and 25 A at start<\/li>\n<li>Route setting can throw two machines simultaneously<\/li>\n<\/ul>\n<p>The design current for the rectifiers is the continuous load plus battery recharge current, not the point machine peaks. With a 100 Ah NiCd battery and a 0.2C recharge limit, that is 12 A + 20 A = 32 A. Using four 15 A rectifier units gives 60 A installed. With one unit failed, 45 A remains, comfortably above 32 A. That configuration is N+1 with margin.<\/p>\n<p>The simultaneous throw peak, 12 A + 2 \u00d7 25 A = 62 A, briefly exceeds the rectifier capacity even with all units healthy. That is acceptable, and expected, because the battery is on the bus. The rectifiers run into current limit for a fraction of a second and the battery supplies the difference. What must be checked is the voltage drop at the far point machine during that peak, at minimum battery voltage.<\/p>\n<h2>Environment and Standards<\/h2>\n<p>Railway DC power equipment lives in harsh places: relay rooms without air conditioning, lineside cabinets, tunnels. Specifications typically address:<\/p>\n<ul>\n<li><strong>EMC:<\/strong> EN 50121-4 for signalling and telecommunications apparatus<\/li>\n<li><strong>RAMS:<\/strong> EN 50126 for reliability, availability, maintainability and safety<\/li>\n<li><strong>Temperature:<\/strong> often -25 \u00b0C to +55 \u00b0C or wider for lineside locations<\/li>\n<li><strong>Vibration and dust:<\/strong> cabinets near the track see both<\/li>\n<\/ul>\n<p><em>Calculated system availability for single, N+1 and N+2 rectifier configurations, using the same per-unit MTBF and repair time.<\/em><\/p>\n<figure id=\"attachment_33797\" aria-describedby=\"caption-attachment-33797\" style=\"width: 1024px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" loading=\"lazy\" class=\"size-large wp-image-33797\" src=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability-1024x576.webp\" alt=\"Availability comparison chart for single, N+1 and N+2 redundant rectifier configurations in railway DC power supplies\" width=\"1024\" height=\"576\" srcset=\"https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability-1024x576.webp 1024w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability-300x169.webp 300w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability-768x432.webp 768w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability-710x399.webp 710w, https:\/\/epcas.com.tr\/wp-content\/uploads\/2026\/11\/railway-rectifier-redundancy-availability.webp 1200w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><figcaption id=\"caption-attachment-33797\" class=\"wp-caption-text\">Availability comparison chart for single, N+1 and N+2 redundant rectifier configurations in railway DC power supplies<\/figcaption><\/figure>\n<h2>Specification Checklist for a Railway DC Power Supply<\/h2>\n<ol>\n<li>Nominal DC voltage (110 V, 125 V or other) and allowed tolerance at the loads<\/li>\n<li>Continuous load current and peak current during simultaneous point throws<\/li>\n<li>Number of point machines that can throw at once<\/li>\n<li>Battery chemistry, autonomy and minimum ambient temperature<\/li>\n<li>Redundancy level (N+1 or N+2) and maintenance philosophy<\/li>\n<li>Earth leakage or insulation monitoring requirements<\/li>\n<li>Alarm outputs to the signalling SCADA: dry contacts, Modbus or IEC 61850<\/li>\n<li>Physical installation: rack, cabinet, wall-mounted, location case<\/li>\n<\/ol>\n<h2>Maintenance and Testing in Service<\/h2>\n<p>A redundant system only stays redundant if failures are noticed. Every rectifier unit should report its status individually to the signalling SCADA, so a failed unit is replaced within days rather than discovered at the next annual inspection. Battery testing matters just as much: a periodic discharge test, or at least a monitored partial discharge, confirms that autonomy is still there before it is needed.<\/p>\n<blockquote><p>Stations that depend on battery backup can review our guide to the <a href=\"https:\/\/epcas.com.tr\/en\/industrial-battery-charger-manufacturer\/\">Industrial Battery Charger<\/a> manufacturer to see how batteries are kept charged.<\/p><\/blockquote>\n<h2>How EPC Energy Approaches Railway Projects<\/h2>\n<p>We design rectifiers and battery chargers for railway applications at our manufacturing facility in Istanbul and test every system at full load before shipment, including failover and current-sharing tests with units removed from service. Our transportation references include DC systems for railway lines, metros and port infrastructure.<\/p>\n<p>If you have a signalling or point machine power requirement, send us the load list and the point machine data sheet. Our engineers will propose a configuration.<\/p>\n<h2>Frequently Asked Questions<\/h2>\n<h3>What DC voltage do railway point machines use?<\/h3>\n<p>Most DC point machines operate at 110 V DC, with 125 V DC also common. The exact voltage depends on the machine type and the operator&#8217;s standard.<\/p>\n<h3>Why do railway DC systems use parallel redundant rectifiers?<\/h3>\n<p>Because all units run at the same time, the loss of one requires no transfer. The others take over its share within milliseconds and the bus never interrupts.<\/p>\n<h3>Why is the battery connected directly to the DC bus?<\/h3>\n<p>It provides autonomy during mains failure and supplies point machine inrush current, keeping bus voltage stable for interlocking equipment.<\/p>\n<h3>Why do railway DC systems need earth leakage detection?<\/h3>\n<p>They are operated unearthed. A first insulation fault is harmless, but a second fault on the other pole can create unsafe current paths. Monitoring detects the first fault early.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>On a railway, very few things are allowed to fail quietly. A signal that goes dark defaults to danger and stops trains. A set of points that loses power in mid-throw leaves a route unproven, and the interlocking will not clear a signal over it. Either way, traffic stops. The railway DC power supply behind [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":33788,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"nf_dc_page":"","nfd_image_url":"","nfd_onboarding_generated":"","footnotes":""},"categories":[504],"tags":[],"class_list":["post-33786","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-articles"],"_links":{"self":[{"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/posts\/33786","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/comments?post=33786"}],"version-history":[{"count":1,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/posts\/33786\/revisions"}],"predecessor-version":[{"id":33799,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/posts\/33786\/revisions\/33799"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/media\/33788"}],"wp:attachment":[{"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/media?parent=33786"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/categories?post=33786"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/epcas.com.tr\/en\/wp-json\/wp\/v2\/tags?post=33786"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}